LeadChem Technical enquiry

Engineering resources

Quality testing & validation benchmarks

Agree reproducible trials from catalogue conditions. Values are typical references; confirm current TDS/SDS and test the actual substrate construction.

What is the ambient fiber-tear benchmark?

Condition bonded samples for 24 hours at 5–35°C, then inspect for opening and hand-tear fiber separation. The stated criteria are zero opening and at least 90% fiber tear; the M-6123–M-6328 rigid-box series states at least 95%. Agree the sample construction and inspection method before comparison.

Ambient bond evaluation
SeriesConditioningStated pass criteria
Packaging adhesives24 h at 5–35°CZero opening; hand-tear fiber tear ≥90%
Rigid-box adhesives24 h at 5–35°CZero opening; hand-tear fiber tear ≥95%

Which cold and hot exposures apply to each adhesive series?

Folder-gluer grades such as M-6140 and M-6145 use the −20°C and 60°C reference exposures below. Rigid-box grades such as M-6123 and M-6192 use −36°C and 80°C exposures. These are separate conditioning protocols, not a continuous service-temperature rating or proof that every bonded construction will pass.

Temperature and humidity exposure references
SeriesCold exposureHot exposure
Folder-gluer cold glue−20°C / 24 h60°C / 24 h at 85% RH
Rigid-box cold glue−36°C / 24 h80°C / 48 h at 95% RH

How are nozzle cleaning, foaming and glue slinging evaluated?

The spray benchmark uses 10 kg of continuous application, an average nozzle-wipe interval of at least 30 minutes and cleaned residue area no greater than 20%. Roller and disc checks use 4-hour and 10-minute runs respectively. Confirm the applicable grade, equipment settings and scoring procedure before treating these as acceptance limits.

Application evaluation checkpoints
ApplicationRun conditionObservation or benchmark
Spray gun10 kg continuous sprayingAverage nozzle-wipe interval ≥30 min; cleaned residue area ≤20%
Roller4 h runningInspect foam and residue retained by 160-mesh filtration
Disc10 min runningAssess glue slinging and stability; folder-gluer series reference up to 420 m/min

Which packaging sizes should a sampling enquiry specify?

Request a 20 kg pail, 50 kg drum or 1000 kg IBC tote according to the trial or production plan. State the required grade, destination and current TDS/SDS request. Confirm format availability, storage conditions and handling requirements for that grade; the packaging list does not establish stock or delivery timing.

Packaging formats to request
FormatNet massPlanning use
Pail20 kgSmall-batch / trial
Drum50 kgStandard
IBC tote1000 kgBulk

What do these benchmarks establish before a production trial?

These source-stated benchmarks define questions to resolve with the manufacturing partner, including method, substrate and acceptance timing. They do not constitute certification or a guarantee for another construction. The following answers separate the 24-hour inspection, 48-hour cure reference and grade-specific coating results from a completed production validation.

Does a 24-hour inspection replace the 48-hour cure reference?

No. The ambient inspection follows 24 hours of conditioning; adhesive series separately state a 48-hour cure reference. Record both requirements and agree the final acceptance point.

Does the rigid-box temperature range certify ocean freight?

No. The −36°C and 80°C exposures are test conditions. They do not reproduce every shipping route, load or humidity cycle; validate the packed article for its intended distribution.

Is 420 m/min guaranteed for every folder-gluer job?

No. Up to 420 m/min is a series reference. Confirm board, coating, bead placement, applicator and compression conditions for the selected M-6140–M-6288 grade and actual line.

What must accompany the 3H and 1,000-rub figures?

LK1042 states pencil hardness 3H; LK1044 states no scratch after 1,000 rubs. Request the test method, substrate, cure conditions, load and evaluation criteria before comparing these figures with another product.

Does the 100°C boil result establish retort suitability?

No. LK1037 states no delamination after a 100°C boil for 2 hours. That result alone does not establish suitability for a different pressure, sterilization cycle, food contact or complete laminate construction.

What is needed before accepting a trial batch?

Identify grade, batch, substrates, setup, conditioning and acceptance method. Request current TDS/SDS and retain controls; catalogue benchmarks are not a batch-specific test certificate.