LeadChem Technical enquiry

Water-based coatings & inks

Compare gravure and flexographic inks, aqueous overprint varnishes, functional coatings, lamination adhesives and heat-seal adhesives. Select the operation and both surfaces before comparing a specification.

Compare 15 grades
Blue printed board with a white motif and an exposed paper edge

Which water-based system matches the print, finish or bond?

Start with the operation: LK1035/LK1036 serve gravure printing, LK1028 serves flexo, and LK1021/LK1030 provide gloss or matte aqueous OPV. Functional layers need a separate target: LK1037 states a 100°C, 2 h boil benchmark, while LK1039 states heat-seal strength ≥30 N/15 mm. Validate the selected grade on the complete structure.

Print the image

For gravure, distinguish white LK1035 from blue LK1036; the listed films are corona treated. LK1028 is the flexographic color grade. Identify the press, anilox or cylinder, color reference, treated face and drying conditions; a film name alone does not establish adhesion.

Choose the overprint finish

Use aqueous coating / water-based OPV terminology when specifying LK1021 gloss, LK1030 matte or LK1022 inline varnish. LK1033 is the soft-touch route. Confirm surface feel, appearance, stack behavior and later foil stamping or gluing on the same print sample.

Define the functional layer

LK1024 targets metallized or holographic card; LK1025 targets foil coating; LK1029 targets transfer film. Separate these operations from LK1038 paper/PET or PE lamination, LK1026 metallized-film lamination and LK1039 heat sealing. The structure and test conditions determine the trial.

Which solids, viscosity and performance figures are available for each grade?

The 15 grades below retain the supplied ranges and identify missing methods. LK1035 and LK1036 explicitly use Tu-4 seconds at 25°C; other seconds-based entries do not identify a cup. LK1038, LK1026 and LK1039 use mPa·s. Compare only measurements with matching methods and confirm every production specification in the current TDS.

Typical/source-stated data for initial selection; confirm the latest TDS/SDS and substrate trial.
GradeSolidsViscosityKey test benchmarkTarget substratesApplication method
LK1035 Water-Based Gravure White InkRequest TDS / sample Not specified 20–30 s (Tu-4 cup, 25°C) pH 8.0–9.0 Corona-treated BOPP, PET; paper packaging Gravure printing
LK1036 Water-Based Gravure Blue InkRequest TDS / sample Not specified 18–28 s (Tu-4 cup, 25°C) pH 8.0–9.0 Corona-treated BOPP, PET, PVC film Gravure printing
LK1028 Water-Based Flexo General Color InkRequest TDS / sample ≥40% 25–35 s; cup/temperature not specified pH 7.5–8.5; solvent-free formulation stated Paper, board, flexible films, labels Flexographic printing
LK1021 Water-Based High-Gloss Varnish / Aqueous Gloss OPVRequest TDS / sample ≥35% Not specified Gloss ≥85° (60° geometry as supplied) Printed paper, gift boxes, plastics Aqueous overprint coating; confirm coating unit
LK1022 Water-Based Inline Varnish / Inline Aqueous OPVRequest TDS / sample 40±1% 40±10 s; cup/temperature not specified Inline drying and anti-blocking; no numeric acceptance limit supplied Cigarette packs, cartons, gift boxes, bags, labels Inline aqueous coating
LK1030 Water-Based Matte Varnish / Aqueous Matte OPVRequest TDS / sample ≥32% Not specified Gloss 15–30° (60° geometry as supplied) Books, catalogs, gift packaging, plastics Aqueous overprint coating; confirm coating unit
LK1024 Water-Based Metallized Card Varnish / PrimerRequest TDS / sample 30±1% 20±2 s; cup/temperature not specified Wetting and adhesion on metallized stock; numerical limit not supplied Transfer/metallized and holographic card Water-based primer/coating; confirm coating unit
LK1025 Water-Based Aluminum Foil VarnishRequest TDS / sample 25±1% 20±2 s; cup/temperature not specified Flexible clear film; adhesion/abrasion/water-resistance limits not supplied Aluminum foil, foil-laminated paper, labels Water-based foil coating; confirm coating unit
LK1033 Water-Based Soft-Touch VarnishRequest TDS / sample By grade; confirm TDS 50±5 s; cup/temperature not specified Velvet/skin-like matte feel; no numeric rub or scratch limit supplied Cartons, tobacco, cosmetic and wine boxes Water-based tactile coating; confirm coating unit
LK1034 Water-Based Water-Resistant VarnishRequest TDS / sample 30±1% 40±10 s; cup/temperature not specified Water droplets and short-term moisture; duration not specified Paper, board, bags, labels Water-based surface coating; confirm coating unit
LK1037 Water-Based Boil-Resistant CoatingRequest TDS / sample ≥40% Not specified 100°C water boil for 2 h without delamination Food-packaging structures, pouch structures, outdoor labels; validate intended use Water-based functional coating; confirm coating unit
LK1029 Water-Based Transfer-Film CoatingRequest TDS / sample ≥38% 35–55 s; cup/temperature not specified Peel strength ≥1.5 N/15 mm Hot-stamping and metallized transfer film Transfer coating
LK1038 Paper-Plastic Lamination AdhesiveRequest TDS / sample ≥45% 500–1000 mPa·s Bond and aging resistance; numeric test limits not supplied Paper to PET or PE film Paper-film lamination
LK1026 Metallized-Film Lamination AdhesiveRequest TDS / sample ≥42% 800–1500 mPa·s Non-corrosive to aluminum layer is a stated characteristic Metallized film, foil, barrier laminates Lamination
LK1039 Water-Based Heat-Seal AdhesiveRequest TDS / sample ≥40% 300–800 mPa·s Heat-seal strength ≥30 N/15 mm Food and pharmaceutical packaging structures; validate intended use Heat-seal coating; confirm temperature, pressure and dwell

Solids describe the non-volatile fraction, not a universal performance ranking. Higher solids can alter deposited dry material at a fixed wet application mass, but drying, wetting and coat-weight requirements still depend on the grade and substrate. Gloss units and geometry are reproduced as supplied; confirm the instrument and method before comparing results.

Tu-4 / DIN / Zahn reference: LK1035 and LK1036 retain their Tu-4 cup specification at 25°C. DIN 4, Zahn #2/#3 and mPa·s comparisons are approximate screening references only: cup geometry, valid flow-time range, liquid density and flow behavior matter. Other viscosity values in seconds do not identify a cup in the supplied data. Review the viscosity tool and its measurement limits.

Read grade-specific data and method limits
  • LK1035: High opacity, low odor and easy dispersion are stated characteristics; confirm opacity and odor on the intended print. Source-stated characteristics: High opacity, low odor and easy dispersion. Qualitative claims require the applicable method and substrate trial.
  • LK1036: Color, rub resistance, settling and leveling require a substrate and process trial. Source-stated characteristics: Bright color, rub resistance, low settling and smooth leveling. Qualitative claims require the applicable method and substrate trial.
  • LK1028: Cup and test temperature not specified in the supplied data; confirm the current TDS. Source-stated characteristics: Fast drying, clear dots, water resistance and a solvent-free formulation. Qualitative claims require the applicable method and substrate trial.
  • LK1021: Abrasion and alcohol resistance are stated characteristics; test method and acceptance limits require confirmation. Source-stated characteristics: Abrasion and alcohol resistance, with leveling. Qualitative claims require the applicable method and substrate trial.
  • LK1022: Cup and test temperature not specified in the supplied data; confirm the current TDS. Source-stated characteristics: Inline drying, transfer, leveling, abrasion resistance and anti-blocking. Qualitative claims require the applicable method and substrate trial.
  • LK1030: Source-stated characteristics: Matte appearance, scratch resistance, low whitening and anti-yellowing. Qualitative claims require the applicable method and substrate trial.
  • LK1024: Cup and test temperature not specified in the supplied data; confirm the current TDS. Source-stated characteristics: Wetting and adhesion while retaining the metallic appearance. Qualitative claims require the applicable method and substrate trial.
  • LK1025: Cup and test temperature not specified in the supplied data; confirm the current TDS. Source-stated characteristics: Clear, flexible film with adhesion, abrasion and water resistance. Qualitative claims require the applicable method and substrate trial.
  • LK1033: Cup and test temperature not specified in the supplied data; confirm the current TDS. Source-stated characteristics: Velvet/skin-like feel, uniform matte appearance, wear and scratch resistance. Qualitative claims require the applicable method and substrate trial.
  • LK1034: Cup and test temperature not specified in the supplied data; confirm the current TDS. Source-stated characteristics: Resistance to water droplets and short-term moisture, clear appearance and abrasion resistance. Qualitative claims require the applicable method and substrate trial.
  • LK1037: The supplied application list includes retort pouches. The 100°C boil benchmark does not establish pressurized retort sterilization or food-contact compliance. Source-stated characteristics: Boil and pressure resistance, adhesion and flexibility; the only numerical heat exposure supplied is the 100°C water-boil test. Qualitative claims require the applicable method and substrate trial.
  • LK1029: Cup and test temperature not specified in the supplied data; confirm the current TDS. Peel test conditions require confirmation. Source-stated characteristics: Transfer stability and peel strength for metallized transfer films. Qualitative claims require the applicable method and substrate trial.
  • LK1038: Source-stated characteristics: Bond strength, aging resistance and high-speed paper/film lamination; no numeric line-speed limit supplied. Qualitative claims require the applicable method and substrate trial.
  • LK1026: Check corrosion and bond retention on the actual metallized layer; no corrosion test method is supplied. Source-stated characteristics: Adhesion to metallized layers, weather resistance and non-corrosiveness to aluminum. Qualitative claims require the applicable method and substrate trial.
  • LK1039: Seal conditions are not supplied. A strength figure is not a food-contact or pharmaceutical compliance certificate. Source-stated characteristics: Low sealing temperature, low-temperature resistance and low odor; no numeric sealing or low-temperature operating window supplied. Qualitative claims require the applicable method and substrate trial.

What should be checked when an aqueous coating or film bond fails?

For LK1022 blocking at its stated 40±1% solids, check drying, coating weight and stack conditions before changing grade. For LK1035/LK1036 film adhesion, check the treated side and current surface condition. For metallized structures, distinguish LK1025 foil coating from LK1026 lamination adhesive. The matrix lists possible causes to investigate, not confirmed diagnoses or guaranteed remedies.

Possible causes to investigate; validate the selected grade and process adjustment on your line.
Production defectPossible root causeRecommended grade & process checks
Inline varnish blockingIncomplete drying, excessive wet coat weight, warm stacking or pressure may contribute.Screen LK1022 for the actual inline unit. Check coat weight, air/heat balance and stack temperature; validate a stack-block test before increasing speed.
BOPP/PET ink adhesion failureWrong or aged treated face, contamination, unsuitable drying or a film/ink mismatch may contribute.Screen LK1035/LK1036 on the stated corona-treated film. Record treatment condition and drying; do not infer an unstated dyne target or dilute without grade guidance.
Aluminum-layer corrosion or loss of bondLayer chemistry, moisture, residual chemicals or an incompatible material may contribute; failure location must be established.For lamination, investigate LK1026, whose aluminum non-corrosiveness is source-stated. LK1025 serves foil coating. Trial the actual layer and aging conditions; neither statement establishes every structure's compatibility.
Film-to-paper delaminationWetting, adhesive coat weight, drying, nip contact or the two bonding surfaces may be unsuitable.Screen LK1038 for paper/PET or PE and LK1026 for metallized structures. Record the failure face and compare peel after agreed conditioning.
Peel or seal below the agreed targetFilm construction, sealing/transfer conditions or test procedure may differ from the source benchmark.LK1029 states ≥1.5 N/15 mm peel; LK1039 states ≥30 N/15 mm heat seal. Request the original method and compare temperature, pressure and dwell before adjusting.

Which substrate checks should accompany a water-based material trial?

Send representative substrate samples, the printing or coating setup, the required finish and the conditioning test. For LK1035/LK1036, include treated-film details; for LK1024/LK1025, identify the metallic layer. For LK1033, with stated viscosity 50±5 s, include the tactile reference and later gluing. Use the substrate guides and QC benchmarks to define acceptance before ordering.

What do buyers need to confirm before ordering water-based grades?

The main checks are the operation, exact substrate, measurement method and intended end use. LK1037's 100°C boil figure, LK1039's seal strength and LK1029's peel strength each describe a different test. None establishes universal compatibility or regulatory approval. The answers below identify the evidence and the information needed for a selection request.

Which aqueous OPV grades cover gloss, matte and inline coating?

LK1021 is the gloss OPV with solids ≥35% and stated gloss ≥85° at 60° geometry. LK1030 is the matte OPV with solids ≥32% and stated gloss 15–30°. LK1022 is the inline grade with 40±1% solids. Confirm the coating unit, drying capacity, coat weight and downstream gluing.

Can LK1035 and LK1036 print directly on untreated BOPP or PET?

The stated film applications for LK1035 and LK1036 use corona-treated surfaces. Their viscosity ranges are 20–30 s and 18–28 s respectively, measured with a Tu-4 cup at 25°C. Provide the film, treated side, treatment age and drying conditions; neither specification establishes adhesion on untreated film.

Does the LK1037 boil benchmark prove retort or food-contact approval?

LK1037 has a stated 100°C water-boil benchmark of 2 h without delamination and solids ≥40%. That result does not establish pressurized retort sterilization or regulatory clearance. Identify the full packaging structure, temperature profile, contents and destination market, then request the applicable TDS, SDS and supporting compliance documentation.

How do LK1038, LK1026 and LK1039 differ?

LK1038 targets paper-to-PET/PE lamination at 500–1000 mPa·s. LK1026 targets metallized-film and foil laminates at 800–1500 mPa·s, with non-corrosiveness to aluminum stated. LK1039 is a heat-seal adhesive at 300–800 mPa·s with a stated ≥30 N/15 mm seal benchmark. Confirm layer structure and production conditions before choosing.

Can every viscosity in seconds be treated as a Tu-4 result?

No. Only LK1035 and LK1036 explicitly identify a Tu-4 cup and 25°C in the supplied specifications. Other second-based entries retain their original numbers with cup and temperature unconfirmed. Request the measurement method before comparing them with DIN 4, Zahn #2/#3 or dynamic viscosity in mPa·s.

What should a trial request include for soft-touch or metallized packaging?

For LK1033 soft-touch varnish, LK1024 metallized-card primer or LK1025 foil varnish, send the substrate and any existing finish, the coating unit, drying conditions and intended performance check. LK1033 states 50±5 s; LK1024 and LK1025 state 20±2 s, with cup methods unconfirmed. Include packaging size and TDS/SDS requirements.

Typical/source-stated values support initial screening. They are not certifications or warranties. Confirm the latest TDS/SDS, test methods and the complete substrate/process trial before production. Packaging options: 20 kg pail, 50 kg drum and 1000 kg IBC tote.